www.6988成人A片四虎,亚洲无码视频在线,色狠狠色噜噜AV天堂五区消防,97精品无码一区二区三区蜜桃,欧美人妻日韩精品

Effect of film blowing process on film properties

2021-03-27 5

Blown film technology

The process flow of blown film is plasticizing and extruding material to form tube blank, which is inflated, cooled, pulled and coiled. In the process of blown film forming, according to the different extrusion and traction directions, it can be divided into three kinds: flat extrusion up blowing method, flat extrusion down blowing method and flat extrusion flat blowing method.

1. Flat extrusion and top blowing

In this method, a right angle die is used, that is, the discharge direction of the die is perpendicular to the extruder, the extruded tube billet is pulled up to a certain distance, and then it is clamped by a herringbone plate. The extruded tube is inflated into a foam tube by the compressed air introduced from the bottom, and its transverse dimension is controlled by the amount of compressed air, and the longitudinal dimension is controlled by the traction speed. The blown thin foam tube can be obtained by cooling and shaping Membrane.

Due to the tenacity and stable traction of the foam hanging on the top of the membrane tube, it can produce a wide range of thickness and wide film, so it is most widely used. The main plastic varieties suitable for up blowing method are PVC, PE, PS and HDPE, especially the wide film of PVC and PE.

2. Flat extrusion blow down method

Down blowing method has a good cooling effect because the tube billet is pulled downward, and the film is drawn into the traction roll by self weight, so the operation of film drawing is more convenient. However, the installation of the machine is too high, and the film bubble is hung on the plastic section which has not been cooled and shaped. When the pulling speed is fast or the production of thick film and the material density is large, it is easy to break the tube film PP, PA, PVDC (vinylidene chloride) and other high crystallinity plastics, to reduce the crystallinity by quenching.

3. Flat extrusion and flat blowing

This method uses a straight die concentric with the screw of the extruder, and the foam pipe and the center line of the die are on the same horizontal plane, which is called flat extrusion and flat blowing method. This method is only suitable for blowing small diameter film products, such as LDPE, PVC, PS film. The flat blowing method is also suitable for the production of blown heat shrinkable films.

Main process factors affecting blown film

There are many factors that affect the stability of blown film processing. Understanding these factors is conducive to the control of the production process, and also to improve the physical and mechanical properties and appearance quality of the film.

1. Temperature control

Temperature control is a key link in film production, which directly affects the product quality. There are two kinds of temperature control conditions: one is that the temperature gradually rises from the charging section of the fuselage to the exit of the nose; the other is that the temperature of the middle and front sections of the fuselage is the highest, and the temperature of the nose is lower. For the equipment with small aspect ratio, especially the transparency, the second method is used. The selection of temperature in each section of the main engine is related to the materials used. If the extruder with diameter of 65 mm, length diameter ratio of 20:1 and compression ratio of 3:1 is used to produce PE film, the temperature control is as follows: feeding section 140-150 ℃, middle section 170-180 ℃, front section 180-190 ℃ and die head 180 ℃.

2. Expansion and traction of membrane tube

The molten material is extruded from the die head to form a cylindrical tube blank. At the same time, air is introduced into the die to inflate the film blank into a film bubble. The formation of the film bubble makes the melt stretch and thin, and combines with the stretch caused by the traction effect to form a biaxial tensile film. In order to prepare films with equal longitudinal and transverse strength, it is required that the transverse blowing ratio (the ratio of the bubble diameter to the die diameter) and the longitudinal drafting ratio (the ratio of the linear velocity of the drawn film tube to that of the non drawn film tube) should be the same. In the actual production, the die with the same specification is often used to make films with different thickness and width by adjusting the blowing ratio and traction ratio.

The blow up ratio is usually controlled at 1.5-3. If the blow up ratio is too small, the transverse strength is low; if the blow up ratio is too large, the process stability, film forming and production continuity are low. The draft ratio is generally controlled between 3 and 7. In production practice, the draft ratio is determined when the film thickness, blowing ratio and film gap are determined. Therefore, adjusting the draft ratio is a way to adjust the film thickness. In order to reduce the film thickness, the traction speed can be increased, that is, the draft ratio should be increased, but the film tube should be prevented from being broken when the draft ratio is too large.

3. Cooling and setting

The cooling of film tube is very important. It should be air-cooled immediately after blowing. If the air cooling is not good, the film will stick and cannot be lifted, or they will stick to each other under the pressure of traction roller. Therefore, the cooling effect and cooling rate will directly affect the quality and output of products. The common cooling method is to use compressed air to blow directly around the membrane bubble through the wind ring. In order to improve the cooling effect, cooling air, secondary air ring, mandrel inner cooling and other technologies are also used.


又大又粗又大又爽又黄 | 国产日韩一区二区三 | 亚洲AV无码成人精品 | 国产suv一区二区 | 可以免费看的黄视频 | 成人红桃a视频一区 | 中文字幕av永久免费在线 | 四川BBB搡BBB搡多人乱亂 | 极品97尤物被啪到呻吟喷水 | 欧美黑人精品无码久久久 | 夜夜春亚洲嫩草直播蜜桃 | 国产一级毛片一级A片酒瓶 五十老熟妇乱子伦免费章节 | 91极品美女裸身网站直播 | 国产精品多人高p无码 | 成人网欧美在线视频 | 日本无码a午夜精品一区 | 精品秘 无码一区二区久久 国产精久久 网站漫画 | EEUSS鲁丝片无码入口 | 国产互换人妻XXXX69张雅丹 | 国产高清一级AV片 | 国产黄色无码视频国产 | 可以看国产黄色视频的网站 | 国产精品精品久久久久久 | 成人影院午夜男女爽爽爽软件 | 色欲无码婬片A片AAA毛片卡通 | 成人自慰网址免费观看 | 日本人成A片在线一区二区 人人添人人澡人人爽人人澡 | 国产精品久久久一本精品重冂色情 | 亚洲高清视频一区 | www,国人在线人妻偷拍 | 一本一道久久a久久精品蜜桃 | 免费无码又爽又高潮视频软件 | 少妇无码破解视频中文字幕 | 人妻熟女一区二区三区 | 美人少妇自慰多水成人A片一区 | 国产精品久久久精品香蕉 | 奴色虐aV一区二区三区 | 国产精品成AV人在线视午夜片 | 婷婷五月天激情激情 | 国产老熟女伦老熟妇A片小川桃果 | 1024人妻一区二区三区 |